P7040002.JPGLeading edge162 viewsLE preparation
|
|
P7040001.JPGClearcoating155 viewsApplying coating to inner of leading edges.
|
|
P7060004.JPGLeading edge158 viewsFrom storage
|
|
P7060003.JPGLeading edge180 viewsFrom storage
|
|
P7060005.JPGBridging the gap174 views..something for the LE ply to glue to..
|
|
P8010011.JPGLeading edge158 viewsClearcoating
|
|
P8040001.JPGLeading edge167 viewsUsing nailers to hold during curing
|
|
P8040002.JPGLeading edge148 viewstrimming off with laminate trimmer
|
|
P8070023.JPGIdler153 viewsIdler and bracket
|
|
P8070024.JPGBellcrank139 viewsBellcrank and bracket
|
|
P8070025.JPGBellcrank169 viewsBellcrank and bracket
|
|
P8070026.JPGLeading edge174 viewsClearcoated
|
|
P8110004.JPGAileron Hinge169 viewsHinge well shot
|
|
P8110005.JPGClearcoat soaking178 viewsSyringe for applying Clearcoat into holes
|
|
P8160006.JPGAileron pushrod169 viewsDremel for clearance
|
|
P8160007.JPGAileron pushrod141 viewsDremel for clearance
|
|
P8160008.JPGAileron pushrod148 viewsDremel for clearance
|
|
P8160009.JPGCompression strut151 viewsDremel for clearance
|
|
P8170010.JPGAileron well185 viewsSoaking in dishwasher cycle
|
|
P8170011.JPGCompression strut165 viewsAileron pushrod clearance
|
|
P8200002.JPGAileron well173 viewsUsing paper as a template
|
|
P8200003.JPGAileron well177 viewsCloaking with 1/32 ply
|
|
P8200004.JPGAileron well171 viewsForming
|
|
P8200005.JPGAileron well167 viewsClamping
|
|
P8230006.JPGPly doublers154 viewsNotching on table saw
|
|
P8230008.JPGWing walk detail181 viewsFirst inner bay
|
|
P8240001.JPGWing walk & idler171 viewsInner bay
|
|
P4060076.jpgSpar tip96 viewsCutting the taper
|
|
P4050075.jpgSpar tip91 viewsMarking out the taper
|
|
P4060078.jpgSpar tip97 viewsDone
|
|
P4100043.JPGDrag blocks104 viewsJust dadoe'd
|
|
P4110042.jpgWing119 viewsPerspective
|
|
P4110044.jpgInner ribs101 views
|
|
P4120043.jpgDrag block103 views
|
|
P4130046.jpgCompression rib94 viewsClamped on with nailers
|
|
P4140043.JPGHardware103 viewsNicely packaged for good order :0)
|
|
P4150048.jpgI-strut103 views1/4 ply
|
|
P4150058.jpgDrag block114 views1/4 ply doublers notched
|
|
P4260069.jpgWing111 viewsSetting the other ribs
|
|
P4270070.JPGTrailing edge115 viewsCutting with aviation snips
|
|
P4160061.jpgTip bow fitting119 viewsMarking cut off point for tip bow
|
|
P4270072.jpgTrailing edge116 viewsclamping with cable ties
|
|
P4290003.jpgWing131 viewsCorner bracing
|
|
P4290007.jpgCapstrip flushing136 viewsBro in law Rick, literally posing for the shot [router is off!]
|
|
P5030009.jpgAileron well134 viewsFitting the sub trailing edge
|
|
P5140015.jpgDrag wires122 viewsEpoxy spraying the 4130
|
|
P5100007.jpgBeej +Wing143 viewsClearcoating
|
|
P5160001.jpgSpar butt fittings130 viewsIn situ
|
|
P5160004.jpgSpar butt fittings138 viewsIn situ
|
|
P5170013.jpgAileron well129 viewsFinished trailing edge
|
|
P5170015.jpgTip bow135 viewsSet
|
|
P5280001.jpgDrag block122 views4130 steel washers...
|
|
P5280004.jpgFiller124 viewsSuperfil from ASS
|
|
P5280005.jpgAdding weight131 viewsFrom one end of the wing too the other I had a 1/32 bounce
|
|
P5310001.JPGNose rib126 viewsDoubler for leading edge ply [fits in 2 pieces]
|
|
P5310002.JPGSpar butt156 viewsHardware
|
|
P5310004.JPGWing127 viewsDrag wires [the spring scale was a bad idea]
|
|
P6050001.jpgTip123 viewsglueing in the foam
|
|
P6040005.JPGwing121 viewsTramelling
|
|
P6090006.JPGTip118 viewsglueing in the foam
|
|
P6120011.JPGTip128 viewsFinally sanded
|
|
P8300001.jpgWing walk147 viewsFirst layer of ply
|
|
P8310002.jpgWing walk162 viewsFinal filling with Superfil [extremely lightweight]
|
|
P9010001.jpgWing walk150 viewsView from underside
|
|
P9010004.jpgTip144 viewsTip finally finished with clearcoat
|
|
P9030008.jpgWing Done!150 viewsHanging on the wall...yeehaaa
|
|
P2110041b.jpgvent hole125 viewsbug mesh
|
|
|
|
|
|
